How To Drill A Door For A Mortise Lock

Use a bevel edge chisel and hammer to square the corners of the mortise if the faceplate has square corners. To install a mortise lock into a wood or composite door requires a pocket drilled into the edge of the door with the centerline of the door prep at 39 3 16 above the finished floor. Drill the holes for the spindle and keyhole make the spindle hole at least as big as the spindle boss of the lock for the keyhole drill the top hole and cut out the shape using a thin pad saw.

insulating attic access stairs hardwood vs laminate vs vinyl vs tile how to make a roofing contract hidden electronic cabinet locks hickory white sofa table install roof bag gx460 how to fix felt roof shingles how to hang wall decorations without nails

Deadbolt Door Lock Bump Pick Drill Proof High Security Mortise Wood Metal Doors Metal Door Door Locks Deadbolt

Deadbolt Door Lock Bump Pick Drill Proof High Security Mortise Wood Metal Doors 700617307072 Ebay Metal Door Door Fittings Deadbolt

Deadbolt Door Lock Bump Pick Drill Proof High Security Mortise Wood Metal Doors 700617307072 Ebay Metal Door Door Lock Security Door Locks

How To Make A New Key For An Old Mortise Lock Mortise Lock Lock Repair Skeleton Key Lock

How To Install A Lockset Installation Diy Home Improvement Mortise Lock

90mm Mortice Lock Fitting Jig Kit Carbide Tip Wood Cutter Tool 16 5 20 22 25mm Wood Cutter Mortice Lock Door Fittings

This ensures you don t splinter the wood on the face of the door as you blast through drilling from just one side.

How to drill a door for a mortise lock.

In the early days the pocket was cut out using a brace and bit. Push the keep on and mark a pencil line all the way round the hole inside for the latch. Use the 10mm chisel to square the hole up cutting at the top and bottom first. Fit the latch and faceplate into the door.

With the large hole cut it s now time to drill the small 1 inch hole in the edge of the door. The brace is a u shaped steel hand tool that has a wood cap on one end and a bit chuck on the other. Step 11 install the strike plate photo by david carmack. How to cut a mortise for a deadbolt lock.

Use a 7 8 inch spade bit to drill two partially overlapping 5 8 inch deep holes centered above and below the midpoint inset. Use the chisel to deepen the outline marks. Create the mortise using a router attachment remove the wood between the pencil lines drawn on the door edge to create a mortise for the faceplate. Carefully remove the timber inside the lines using the same technique as for the door latch.

You want to drill part way into one side of the door stop and then start to drill from the other side. Make a series of closely spaced cuts into the mortise area. Make a series of. That s what this video is here for.

Square up the sides of the mortise with a chisel if necessary. Transfer the positions of the top and bottom of the mortise lock body to the edge of the door. It is not a difficult procedure and all you really need is a power drill with the appropriate bits and maybe. Remove the keep and drill a 16mm hole about 10mm deep.

It will show you how you can drill out the stump of a mortice lock allowing you to get past the lock entirely. Mark the area around the strike plate that you want to install flush with the wood. Trace the outline of the area. This lock can certainly be picked but what if you don t know how or you don t have anything on hand that can serve as a good lock pick.

Hold the strike plate over the mortise and score its outline with a utility knife.

Pin By Robert On Drawer Locks Safe Lock Door Locks Home Security Systems

Is It Possible To Fill In This Door Hole And Put In A New Lock Doors Exterior Door Handles Wood Exterior Door

Picture 3 Of 10 Deadbolt Door Locks Metal Door

Before And After Replace Old Mortise Lock On Front Door Phs Locksmiths Mortise Lock Front Door Locks Doors

Source : pinterest.com